64GA106 datasheet(279/330 Pages) MICROCHIP

279 / 330 page

 2010 Microchip Technology Inc.

DS39905E-page 279

PIC24FJ256GA110 FAMILY

IIL

Input Leakage Current(2,3)

DI50

I/O Ports

—

AVSS  VPIN  VDD,

Pin at high-impedance

DI51

Analog Input Pins

—

AVSS  VPIN  VDD,

Pin at high-impedance

DI55

MCLR

——

AVSS VPIN VDD

DI56

OSC1

—

AVSS VPIN VDD,

XT and HS modes

TABLE 28-7:

DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS (CONTINUED)

DC CHARACTERISTICS

Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated)

Operating temperature

-40°C

 TA  +85°C for Industrial

-40°C

 TA  +125°C for Extended

Param

No.

Sym

Characteristic

Min

Typ(1)

Max

Units

Conditions

Note 1:

Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only

and are not tested.

The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified

levels represent normal operating conditions. Higher leakage current may be measured at different input

voltages.

Negative current is defined as current sourced by the pin.

Refer to Table 1-4 for I/O pins buffer types.

VIH requirements are met when internal pull-ups are enabled.

TABLE 28-8:

DC CHARACTERISTICS: I/O PIN OUTPUT SPECIFICATIONS

DC CHARACTERISTICS

Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated)

Operating temperature

-40°C

 TA  +85°C for Industrial

-40°C

 TA  +125°C for Extended

Param

No.

Sym

Characteristic

Min

Typ(1)

Max

Units

Conditions

VOL

Output Low Voltage

DO10

I/O Ports

—

0.4

IOL = 8.5 mA, VDD = 3.6V

——

0.4

IOL = 6.0 mA, VDD = 2.0V

DO16

OSC2/CLKO

—

0.4

IOL = 8.5 mA, VDD = 3.6V

——

0.4

IOL = 6.0 mA, VDD = 2.0V

VOH

Output High Voltage

DO20

I/O Ports

3.0

—

IOH = -3.0 mA, VDD = 3.6V

2.4

—

IOH = -6.0 mA, VDD = 3.6V

1.65

—

IOH = -1.0 mA, VDD = 2.0V

1.4

—

IOH = -3.0 mA, VDD = 2.0V

DO26

OSC2/CLKO

2.4

—

IOH = -6.0 mA, VDD = 3.6V

1.4

—

IOH = -3.0 mA, VDD = 2.0V

Note 1:

Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. Parameters are for design guidance only

and are not tested.

The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels

represent normal operating conditions. Higher leakage current may be measured at different input voltages.

Negative current is defined as current sourced by the pin.

Refer to Table 1-4 for I/O pins buffer types.

VIH requirements are met when internal pull-ups are enabled.

64GA106 bảng dữ liệu(PDF) 279 Page - Microchip Technology

64GA106 bảng dữ liệu(HTML) 279 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL