ST7FLITE25F1B6 datasheet(141/166 Pages) STMICROELECTRONICS

141 / 166 page

ST7LITE20F2 ST7LITE25F2 ST7LITE29F2

Electrical characteristics

Doc ID 8349 Rev 5

141/166

Check that all recommendations related to ICCCLK and reset circuit have been applied

(seeTable 2: Device pin description)

Check that the power supply is properly decoupled (100nF + 10µF close to the MCU).

Refer to AN1709 and AN2017. If this cannot be done, it is recommended to put a

100nF + 1M

Ω pull-down on the RESET pin.

The capacitors connected on the RESET pin and also the power supply are key to

avoid any startup marginality. In most cases, steps 1 and 2 above are sufficient for a

robust solution. Otherwise: replace 10nF pull-down on the RESET pin with a 5µF to

20µF capacitor.”

Note:

Please refer to Section 12.2.1: Illegal opcode reset for more details.

13.10

Communication interface characteristics

13.10.1

Serial peripheral interface (SPI)

Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified.

Refer to I/O port characteristics for more details on the input/output alternate function

characteristics (SS, SCK, MOSI, MISO).

Table 83.

Serial peripheral interface (SPI)(1)

Subject to general operating conditions for VDD, fOSC, and TA unless otherwise specified.

Symbol

Parameter

Conditions

Min

Max

Unit

fSCK =

1/tc(SCK)

SPI clock frequency

Master

fCPU = 8MHz

fCPU/128 = 0.0625

fCPU/4 = 2

MHz

Slave

fCPU = 8MHz

0fCPU/2 = 4

tr(SCK)

tf(SCK)

SPI clock rise and fall time

−

see I/O port pin description

tsu(SS)

(2)

Data based on design simulation and/or characterization results, not tested in production.

SS setup time(3)

Slave

(4 x TCPU) +150

−

th(SS)

(2)

SS hold time

Slave

120

−

tw(SCKH)

tw(SCKL)

SCK high and low time

Master

Slave

100

−

tsu(MI)

tsu(SI)

Data input setup time

Master

Slave

100

−

th(MI)

th(SI)

Data input hold time

Master

Slave

100

−

ta(SO)

Data output access time

Slave

120

tdis(SO)

Data output disable time

Slave

−

240

tv(SO)

Data output valid time

Slave (after

enable edge)

−

120

th(SO)

Data output hold time

−

tv(MO)

Data output valid time

Master (after

enable edge)

−

120

th(MO)

Data output hold time

−

ST7FLITE25F1B6 bảng dữ liệu(PDF) 141 Page - STMicroelectronics

ST7FLITE25F1B6 bảng dữ liệu(HTML) 141 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL