| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
HT85F2270 bảng dữ liệu(PDF) 172 Page - Holtek Semiconductor Inc |
|
|
|||||||||||||||||||||||||||||
HT85F2270 bảng dữ liệu(HTML) 172 Page - Holtek Semiconductor Inc |
|
172 / 226 page ![]() Rev. 1.00 17� of ��6 �a� 1�� �01� Standard 8051 8-Bit Flash MCU HT85F2260/HT85F2270/HT85F2280 CP0CR Register SFR Address: DEh Bit 7 6 5 4 3 2 1 0 Name — CP0ON CP0POL CP0OUT CP0OS CP0RSTL CP0RST — R/W — R/W R/W R/W R/W R/W R/W — POR — 0 0 0 1 0 0 — Bit 7 Unimplemented, read as “0” Bit 6 CP0ON: Comparator 0 On/Off control 0: Off 1: On This is the Comparator 0 on/off control bit. If the bit is zero the comparator will be switched off and no power consumed even if analog voltages are applied to its inputs. For power sensitive applications this bit should be cleared to zero if the comparator is not used or before the device enters the Power-Down or IDLE mode. Bit 5 CP0POL: Comparator 0 output polarity 0: Output not inverted 1: Output inverted This is the comparator 0 polarity bit. If the bit is zero then the CP0OUT bit will reflect the non-inverted output condition of the comparator. If the bit is high the comparator CP0OUT bit will be inverted. Bit 4 CP0OUT: Comparator 0 output bit CP0POL=0 0: CP0+ < CP0- 1: CP0+ > CP0- CP0POL=1 0: CP0+ > CP0- 1: CP0+ < CP0- This bit stores the comparator 0 output bit. The polarity of the bit is determined by the voltages on the comparator 0 inputs and by the condition of the CP0POL bit. Bit 3 CP0OS: Comparator 0 output path select 0: C0OUT pin 1: Internal use This is the comparator 0 output path select control bit. If the bit is set to “0” and the CP0ON bit is “1” the comparator 0 output is connected to an external C0OUT pin. If the bit is set to “1” or the CP0ON bit is “1” the comparator 0 output signal is only used internally by the device allowing the shared comparator output pin to retain its normal I/O operation. Bit 2 CP0RSTL: Output reset signal select 0: CP0OUT=0 will reset the MCU 1: CP0OUT=1 will reset the MCU The CP0RST bit should be set high first to enable this function. Bit 1 CP0RST: Comparator 0 output to reset MCU function control 0: Disable 1: Enable Bit 0 Unimplemented, read as “0” |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |