SPMCK16Z4MPV20 datasheet(246/500 Pages) FREESCALE

246 / 500 page

MULTICHANNEL COMMUNICATION INTERFACE

M68HC16 Z SERIES

10-6

USER’S MANUAL

Error-detection logic is included to support interprocessor interfacing. A write-collision

detector indicates when an attempt is made to write data to the serial shift register

while a transfer is in progress. A multiple-master mode-fault detector automatically dis-

ables SPI output drivers if more than one MCU simultaneously attempts to become

bus master.

10.3.1 SPI Registers

SPI control registers include the SPI control register (SPCR), the SPI status register

(SPSR), and the SPI data register (SPDR). Refer to D.7.13 SPI Control Register,

D.7.14 SPI Status Register, and D.7.15 SPI Data Register for register bit and field

definitions.

10.3.1.1 SPI Control Register (SPCR)

The SPCR contains parameters for configuring the SPI. The register can be read or

written at any time.

10.3.1.2 SPI Status Register (SPSR)

The SPSR contains SPI status information. Only the SPI can set the bits in this regis-

ter. The CPU reads the register to obtain status information.

10.3.1.3 SPI Data Register (SPDR)

The SPDR is used to transmit and receive data on the serial bus. A write to this register

in the master device initiates transmission or reception of another byte or word. After

a byte or word of data is transmitted, the SPIF status bit is set in both the master and

slave devices.

A read of the SPDR actually reads a buffer. If the first SPIF is not cleared by the time

a second transfer of data from the shift register to the read buffer is initiated, an over-

run condition occurs. In cases of overrun the byte or word causing the overrun is lost.

A write to the SPDR is not buffered and places data directly into the shift register for

transmission.

10.3.2 SPI Pins

Four bidirectional pins are associated with the SPI. The MPAR configures each pin for

either SPI function or general-purpose I/O. The MDDR assigns each pin as either input

or output. The WOMP bit in the SPI control register (SPCR) determines whether each

SPI pin that is configured for output functions as an open-drain output or a normal

CMOS output. The MDDR and WOMP assignments are valid regardless of whether

the pins are configured for SPI use or general-purpose I/O.

The operation of pins configured for SCI use depends on whether the SCI is operating

as a master or a slave, determined by the MSTR bit in the SPCR.

Table 10-3 shows SPI pins and their functions.

Freescale Semiconductor, Inc.

For More Information On This Product,

Go to: www.freescale.com

SPMCK16Z4MPV20 bảng dữ liệu(PDF) 246 Page - Freescale Semiconductor, Inc

SPMCK16Z4MPV20 bảng dữ liệu(HTML) 246 Page - Freescale Semiconductor, Inc

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL