ATmega162 datasheet(172/324 Pages) ATMEL

172 / 324 page

172

2513K–AVR–07/09

ATmega162/V

USART

Initialization

The USART has to be initialized before any communication can take place. The initialization pro-

cess normally consists of setting the baud rate, setting frame format and enabling the

Transmitter or the Receiver depending on the usage. For interrupt driven USART operation, the

Global Interrupt Flag should be cleared (and interrupts globally disabled) when doing the

initialization.

Before doing a re-initialization with changed baud rate or frame format, be sure that there are no

ongoing transmissions during the period the registers are changed. The TXC Flag can be used

to check that the Transmitter has completed all transfers, and the RXC Flag can be used to

check that there are no unread data in the receive buffer. Note that the TXC Flag must be

cleared before each transmission (before UDR is written) if it is used for this purpose.

The following simple USART initialization code examples show one assembly and one C func-

tion that are equal in functionality. The examples assume asynchronous operation using polling

(no interrupts enabled) and a fixed frame format. The baud rate is given as a function parameter.

For the assembly code, the baud rate parameter is assumed to be stored in the r17:r16 Regis-

ters. When the function writes to the UCSRC Register, the URSEL bit (MSB) must be set due to

the sharing of I/O location by UBRRH and UCSRC.

Note:

1. See “About Code Examples” on page 8.

Assembly Code Example

(1)

USART_Init:

; Set baud rate

out

UBRRH, r17

out

UBRRL, r16

; Enable receiver a?d transmitter

ldi

r16, (1<<RXEN)|(1<<TXEN)

out

UCSRB,r16

; Set frame format:?8data, 2stop bit

ldi

r16, (1<<URSEL)|(1<<USBS)|(3<<UCSZ0)

out

UCSRC,r16

ret

C Code Example(1)

#define FOSC 1843200// Clock Speed

#define BAUD 9600

#define MYUBRR FOSC/16/BAUD-1

void

main( void )

{

...

USART_Init ( MYUBRR );

...

}

void

USART_Init( unsigned int ubrr )

{

/* Set baud rate */

UBRRH = (unsigned c?ar)(ubrr>>8);

UBRRL = (unsigned c?ar)ubrr;

/* Enable receiver ?nd transmitter */

UCSRB = (1<<RXEN)|(1<<TX?N);

/* Set frame format? 8data, 2stop bit */

UCSRC = (1<<URSEL)|(1<<U?BS)|(3<<UCSZ0);

}

ATmega162 bảng dữ liệu(PDF) 172 Page - ATMEL Corporation

ATmega162 bảng dữ liệu(HTML) 172 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL