| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/2111B bảng dữ liệu(PDF) 460 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2111B bảng dữ liệu(HTML) 460 Page - Renesas Technology Corp |
|
460 / 582 page ![]() Rev. 1.00, 05/04, page 426 of 544 16.7.3 Setting Range of Analog Power Supply and Other Pins If conditions shown below are not met, the reliability of this LSI may be adversely affected. • Analog input voltage range The voltage applied to analog input pin ANn during A/D conversion should be in the range AVss ≤ ANn ≤ AVref (n = 0 to 5). • Relation between AVcc, AVss and Vcc, Vss For the relationship between AVcc, AVss and Vcc, Vss, set AVss = Vss. If the A/D converter is not used, the AVcc and AVss pins must on no account be left open. • AVref pin reference voltage specification range The reference voltage of the AVref pin should be in the range AVref ≤ AVcc. 16.7.4 Notes on Board Design In board design, digital circuitry and analog circuitry should be as mutually isolated as possible, and layout in which digital circuit signal lines and analog circuit signal lines cross or are in close proximity should be avoided as far as possible. Failure to do so may result in incorrect operation of the analog circuitry due to inductance, adversely affecting A/D conversion values. Also, digital circuitry must be isolated from the analog input signals (AN0 to AN5), analog reference voltage (AV ref), and analog power supply (AVCC) by the analog ground (AVSS). Also, the analog ground (AV SS) should be connected at one point to a stable digital ground (VSS) on the board. 16.7.5 Notes on Noise Countermeasures A protection circuit connected to prevent damage due to an abnormal voltage such as an excessive surge at the analog input pins (AN0 to AN5) and analog reference voltage (AV ref) should be connected between AVcc and AVss as shown in figure 16.8. Also, the bypass capacitors connected to AVcc and AV ref , and the filter capacitor connected to AN0 to AN5, must be connected to AV SS. If a filter capacitor is connected, the input currents at the analog input pins (AN0 to AN5) are averaged, and so an error may arise. Also, when A/D conversion is performed frequently, as in scan mode, if the current charged and discharged by the capacitance of the sample-and-hold circuit in the A/D converter exceeds the current input via the input impedance (R in), an error will arise in the analog input pin voltage. Careful consideration is therefore required when deciding the circuit constants. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |