| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/2111B bảng dữ liệu(PDF) 393 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2111B bảng dữ liệu(HTML) 393 Page - Renesas Technology Corp |
|
393 / 582 page ![]() Rev. 1.00, 05/04, page 359 of 544 14.4.3 Receive Abort This LSI (system side) can forcibly abort transmission from the device connected to it (keyboard side) in the event of a protocol error, etc. In this case, the system holds the clock low. During reception, the keyboard also outputs a clock for synchronization, and the clock is monitored when the keyboard output clock is high. If the clock is low at this time, the keyboard judges that there is an abort request from the system, and data transmission from the keyboard is aborted. Thus the system can abort reception by holding the clock low for a certain period. A sample receive abort processing flowchart is shown in figure 14.7, and the receive abort timing in figure 14.8. Read KBCRL KBF = 0? RXCR3 to RXCR0 ≥ B'1001? Disable receive abort requests Yes Start Receive state Read KBCRH Processing 1 KCLKO = 0 (receive abort request) Retransmit command transmission (data)? KBE = 0 (disable KBBR reception and clear receive counter) Set start bit (KDO = 0) Clear I/O inhibit (KCLKO = 1) Transmit data To transmit operation KBE = 0 (disable KBBR reception and clear receive counter) KBE = 1 (enable KB operation) Clear I/O inhibit (KCLKO = 1) To receive operation [1] Read KBCRL, and if KBF = 1, perform processing 1. [2] Read KBCRH, and if the value of bits RXCR3 to RXCR0 is less than B'1001, write 0 in KCLKO to abort reception. If the value of bits RXCR3 to RXCR0 is B'1001 or greater, wait until stop bit reception is completed, then perform receive data processing, and proceed to the next operation. [3] If the value of bits RXCR3 to RXCR0 is B'1001 or greater, the parity bit is being received. With the PS2 interface, a receive abort request following parity bit reception is disabled. Wait until stop bit reception is completed, perform receive data processing and clear the KBF flag, then proceed to the next operation. Yes No No No Yes [1] [2] [3] Figure 14.7 Sample Receive Abort Processing Flowchart (1) |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |