công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

H8/3028F bảng dữ liệu(PDF) 627 Page - Renesas Technology Corp

tên linh kiện H8/3028F
Giải thích chi tiết về linh kiện  Renesas 16-Bit Single-Chip Microcomputer H8 Family/H8/300H Series
PDF  923 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  RENESAS [Renesas Technology Corp]
Trang chủ  http://www.renesas.com
Logo RENESAS - Renesas Technology Corp

H8/3028F bảng dữ liệu(HTML) 627 Page - Renesas Technology Corp

Back Button H8/3028F Datasheet HTML 623Page - Renesas Technology Corp H8/3028F Datasheet HTML 624Page - Renesas Technology Corp H8/3028F Datasheet HTML 625Page - Renesas Technology Corp H8/3028F Datasheet HTML 626Page - Renesas Technology Corp H8/3028F Datasheet HTML 627Page - Renesas Technology Corp H8/3028F Datasheet HTML 628Page - Renesas Technology Corp H8/3028F Datasheet HTML 629Page - Renesas Technology Corp H8/3028F Datasheet HTML 630Page - Renesas Technology Corp H8/3028F Datasheet HTML 631Page - Renesas Technology Corp Next Button
Zoom Inzoom in Zoom Outzoom out
 627 / 923 page
background image
Rev. 2.00, 09/03, page 597 of 890
3. See section 4.2.2, Reset Sequence, and section 18.11, Flash Memory Programming and
Erasing Precautions. The H8/3028F-ZTAT requires a minimum of 20 system clock
cycles for a reset during operation.
18.5.2
User Program Mode
When set to user program mode, the H8/3028F-ZTAT can program and erase its flash memory by
executing a user program/erase control program. Therefore, on-board reprogramming of the on-
chip flash memory can be carried out by providing on-board means of FWE control and supply of
programming data, and storing a program/erase control program in part of the program area as
necessary.
To select user program mode, select a mode that enables the on-chip ROM (mode 5 or 7), and
apply a high level to the FWE pin. In this mode, on-chip supporting modules other than flash
memory operate as they normally would in modes 5 and 7.
Flash memory programming/erasing should not be carried out in mode 6. When mode 6 is set, the
FWE pin must be driven low.
The flash memory itself cannot be read while being programmed or erased, so the program that
performs programming should be placed in external memory or transferred to RAM and executed
there.
Figure 18.8 shows the execution procedure when user program mode is entered during program
execution in RAM. It is also possible to start from user program mode in a reset-start.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com