| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8/3021 bảng dữ liệu(PDF) 516 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8/3021 bảng dữ liệu(HTML) 516 Page - Renesas Technology Corp |
|
516 / 712 page ![]() 15. ROM Rev.2.00 Mar. 22, 2007 Page 492 of 684 REJ09B0352-0200 15.11 Notes on Flash Memory Programming/Erasing The following describes notes when using the on-board programming mode, RAM emulation function, and PROM mode. 1. Program/erase with the specified voltage and timing. Applied voltages in excess of the rating can permanently damage the device. Use a PROM programmer that supports Renasas Technology microcomputer device type F- ZTAT256V3 with 256-kbyte on-chip flash memory. Do not set the PROM programmer at the HN28F101. If the PROM programmer is set to the HN28F101 by mistake, a high level can be input to the FWE pin and the LSI can be destroyed. 2. Notes on powering on/powering off (See figures 15.17 to 15.19.) Input a high level to the FWE pin after verifying Vcc. Before turning off Vcc, set the FWE pin to a low level. When powering on and powering off the Vcc power supply, fix the FWE pin a low level and set the flash memory to the hardware protection mode. Be sure that the powering on and powering off timing is satisfied even when the power is turned off and back on in the event of a power interruption, etc. If this timing is not satisfied, microcomputer runaway, etc., may cause overprogramming or overerasing and the memory cells may not operate normally. 3. Notes on FWE pin High/Low switching (See figures 15.17 to 15.19.) Input FWE in the state microcomputer operation is verified. If the microcomputer does not satisfy the operation confirmation state, fix the FWE pin at a low level to set the protection mode. To prevent erroneous programming/erasing of flash memory, note the following in FWE pin High/Low switching: • Apply an input to the FWE pin after the V CC voltage has stabilized within the rated voltage. If an input is applied to the FWE pin when the microcomputer V CC voltage does not satisfy the rated voltage (V CC = 3.0 V to 3.6 V), flash memory may be erroneously programmed or erased because the microcomputer is in the unconfirmed state. • Apply an input to the FWE pin when the oscillation has stabilized (after the oscillation stabilization time). When turning on the V CC power, apply an input to the FWE pin after holding the RES pin at a low level during the oscillation stabilization time (t osc1=20ms). Do not apply an input to the FWE pin when oscillation is stopped or unstable. • In the boot mode, perform FWE pin High/Low switching during reset. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |