| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/20203 bảng dữ liệu(PDF) 191 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/20203 bảng dữ liệu(HTML) 191 Page - Renesas Technology Corp |
|
191 / 992 page ![]() Section 7 ROM Rev. 1.00 Oct. 03, 2008 Page 165 of 962 REJ09B0465-0100 7.3.1 EW0 Mode EW0 mode can be selected by transferring the reprogramming-control program to the RAM, branching to the program in the RAM, setting the FMEWMOD bit in FLMCR1 to 0, and setting the FMCMDEN bit in FLMCR1 to 1 (to enable software commands), in this order. Programming and erasure operations can be controlled through software commands. Completion of the software command and related information can be read out from the FLMSTR register. To cause a transition to erase-suspend mode during erasure, set both the FMSPEN and FMSPREQ bits in FLMCR2 to 1 (to enable a transition to erase-suspend mode and to request a transition to erase-suspend mode, respectively). Then wait for the transition time to erase-suspend mode (approximately 50 µs), check that the FMRDY bit in FLMSTR is 1 (ready state), and access the user ROM area. Setting the FMSPREQ bit to 0 resumes erasure. When the interrupt is used, set the interrupt vector offset register (VOFR) such that access to the user ROM area is not generated. That is, the vectors should have addresses within the RAM and point to interrupt processing routine that are also in the RAM. 7.3.2 EW1 Mode EW1 mode can be selected by setting the FMEWMOD bit in FLMCR1 to 1, and then setting the FMCMDEN bit in FLMCR1 to 1 (to enable software commands). Programming and erasure operations can be controlled through software commands. Completion of the software command and related information can be read out from the FLMSTR register. To cause a transition to erase-suspend mode during erasure, set the FMSPEN bit in FLMCR2 to 1 (to enable a transition to erase-suspend mode), and then execute the erasure command. Note that the interrupt for causing a transition to erase-suspend mode must be enabled beforehand. This allows the interrupt request to be accepted when the transition time to erase-suspend mode has elapsed after the erasure command is executed. When an interrupt is requested, the FMSPREQ bit is automatically set to 1 (to request a transition to erase-suspend mode), thus suspending erasure. If erasure has not been completed at the end of interrupt processing (FMERCF = 1 in FLMSTR), resume erasure by setting the FMSPREQ bit to 0. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |