công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

H8S/2456R bảng dữ liệu(PDF) 1158 Page - Renesas Technology Corp

tên linh kiện H8S/2456R
Giải thích chi tiết về linh kiện  16-Bit Single-Chip Microcomputer H8S Family / H8S/2400 Series
PDF  1376 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  RENESAS [Renesas Technology Corp]
Trang chủ  http://www.renesas.com
Logo RENESAS - Renesas Technology Corp

H8S/2456R bảng dữ liệu(HTML) 1158 Page - Renesas Technology Corp

Back Button H8S/2456R Datasheet HTML 1154Page - Renesas Technology Corp H8S/2456R Datasheet HTML 1155Page - Renesas Technology Corp H8S/2456R Datasheet HTML 1156Page - Renesas Technology Corp H8S/2456R Datasheet HTML 1157Page - Renesas Technology Corp H8S/2456R Datasheet HTML 1158Page - Renesas Technology Corp H8S/2456R Datasheet HTML 1159Page - Renesas Technology Corp H8S/2456R Datasheet HTML 1160Page - Renesas Technology Corp H8S/2456R Datasheet HTML 1161Page - Renesas Technology Corp H8S/2456R Datasheet HTML 1162Page - Renesas Technology Corp Next Button
Zoom Inzoom in Zoom Outzoom out
 1158 / 1376 page
background image
Section 22 Flash Memory
Rev. 1.00 Sep. 19, 2008 Page 1128 of 1342
REJ09B0467-0100
22.8
Programmer Mode
Along with the on-board programming mode, this LSI also has a programmer mode as a further
mode for the writing and erasing of programs and data. In the programmer mode, a general-
purpose PROM programmer can be used to freely write programs to the on-chip ROM.
Program/erase is possible on the user MAT. The PROM programmer must support Renesas
microcomputers with 256-Kbyte flash memory as a device type.
A status-polling system is adopted for operation in automatic program, automatic erase, and
status-read modes. In the status-read mode, details of the system’s internal signals are output after
execution of automatic programming or automatic erasure. In the PROM mode, provide a 12-MHz
input-clock signal.
22.9
Serial Communication Interface Specification for Boot Mode
Initiating boot mode enables the boot program to communicate with the host by using the on-chip
SCI_1. The serial communication interface specification is shown below.
(1) Status
The boot program has three states.
1. Bit-Rate-Adjustment State
In this state, the boot program adjusts the bit rate to communicate with the host. Initiating boot
mode enables starting of the boot program and entry to the bit-rate-adjustment state. The
program receives the command from the host to adjust the bit rate. After adjusting the bit rate,
the program enters the inquiry/selection state.
2. Inquiry/Selection State
In this state, the boot program responds to inquiry commands from the host. The device name,
clock mode, and bit rate are selected. After selection of these settings, the program is made to
enter the programming/erasing state by the command for a transition to the
programming/erasing state. The program transfers the libraries required for erasure to the
RAM and erases the user MATs before the transition.
3. Programming/erasing state
Programming and erasure by the boot program take place in this state. The boot program is
made to transfer the programming/erasing programs to the RAM by commands from the host.
Sum checks and blank checks are executed by sending these commands from the host.
These boot program states are shown in figure 22.10.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com