| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/2462 bảng dữ liệu(PDF) 1006 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2462 bảng dữ liệu(HTML) 1006 Page - Renesas Technology Corp |
|
1006 / 1250 page ![]() Section 25 Flash Memory Rev. 2.00 Aug. 20, 2008 Page 958 of 1198 REJ09B0403-0200 After the on-chip program storage area is returned to the user-MAT space, the user procedure program is returned. In the download processing, the values of general registers of the CPU are held. In the download processing, any interrupts are not accepted. However, interrupt requests are held. Therefore, when the user procedure program is returned, the interrupts occur. When the level-detection interrupt requests are to be held, interrupts must be input until the download is ended. When hardware standby mode is entered during download processing, the normal download cannot be guaranteed in the on-chip RAM. Therefore, download must be executed again. Since a stack area of 128 bytes at the maximum is used, the area must be allocated before setting the SCO bit to 1. If a flash memory access by the DTC signal is requested during downloading, the operation cannot be guaranteed. Therefore, an access request by the DTC signal must not be generated. 4. FKEY is cleared to H'00 for protection. 5. The value of the DPFR parameter must be checked and the download result must be confirmed. Check the value of the DPFR parameter (one byte of start address of the download destination specified by FTDAR). If the value is H'00, download has been performed normally. If the value is not H'00, the source that caused download to fail can be investigated by the description below. If the value of the DPFR parameter is the same as before downloading (e.g. H'FF), the address setting of the download destination in FTDAR may be abnormal. In this case, confirm the setting of the TDER bit (bit 7) in FTDAR. If the value of the DPFR parameter is different from before downloading, check the SS bit (bit 2) and the FK bit (bit 1) in the DPFR parameter to ensure that the download program selection and FKEY setting were normal, respectively. 6. The operating frequency is set in the FPEFEQ parameter for initialization. The current frequency of the CPU clock is set to the FPEFEQ parameter value (general register ER0). The settable range of the FPEFEQ parameter is 20 to 34 MHz. When the frequency is set to out of this range, an error is returned to the FPFR parameter of the initialization program and initialization is not performed. For details on the frequency setting, see the description in 25.3.2 (2) (a), Flash programming/erasing frequency parameter (FPEFEQ: general register ER0 of CPU). |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |