| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/2426R bảng dữ liệu(PDF) 1012 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2426R bảng dữ liệu(HTML) 1012 Page - Renesas Technology Corp |
|
1012 / 1302 page ![]() Section 17 A/D Converter Rev. 1.00 Sep. 19, 2008 Page 984 of 1270 REJ09B0466-0100 17.7 Usage Notes 17.7.1 Module Stop Function Setting Operation of the A/D converter can be disabled or enabled using the module stop control register. The initial setting is for operation of the A/D converter to be halted. Register access is enabled by clearing the module stop state. Set the CKS1 and CKS2 bits to 1 to set ADCLK to φ, and clear the ADST, TRGS1, TRGS0, and EXTRGS bits all to 0 to disable A/D conversion when entering module stop state after operation of the A/D converter. After that, set the module stop control register after executing a dummy read by one word. For details, see section 24, Power-Down Modes. 17.7.2 A/D Input Hold Function in Software Standby Mode When this LSI enters software standby mode with A/D conversion enabled, the analog inputs are retained, and the analog power supply current is equal to as during A/D conversion. If the analog power supply current needs to be reduced in software standby mode, set the CKS1 and CKS2 bits to 1 to set ADCLK to φ, and clear the ADST, TRGS1, TRGS0, and EXTRGS bits all to 0 to disable A/D conversion. After that, enter software standby mode after executing a dummy read by one word. 17.7.3 Restarting the A/D Converter When the ADST bit has been cleared to 0, A/D converter stops in synchronization with the ADCLK and then enters the standby sate. After the ADST bit has been cleared, the converter may not actually make the transition to the standby state for up to 10 cycles ( φ), so do not change the channels of the ADCLK, motion mode, or analog input at this time. When restarting the A/D converter right after the ADST bit has been cleared to 0, read the 16 bytes from ADDRA to ADDRH and then start the A/D converter by setting the ADST bit to 1. If the converter is in single mode or one-cycle scan mode, however, the ADST bit can be set to 1 by clearing the ADF bit to 0 after confirming that the ADF bit had been set to 1 on completion of the previous round of conversion. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |