| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
M38K04F2 bảng dữ liệu(PDF) 105 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
M38K04F2 bảng dữ liệu(HTML) 105 Page - Renesas Technology Corp |
|
105 / 328 page ![]() FUNCTIONAL DESCRIPTION Rev.2.00 Oct 05, 2006 page 88 of 112 38K0 Group REJ09B0337-0200 HARDWARE qErase All Blocks Command (2016/2016) By writing the command code “2016” in the first bus cycle and the confirmation command code “2016” in the second bus cycle that follows, the operation of erase all blocks (erase and erase verify) starts. Whether the erase all blocks command is terminated can be con- ____ firmed by reading the status register or the RY/BY Status Flag of flash memory control register. When the erase all blocks operation starts, the read status register mode is entered automatically and the contents of the status register can be read out at the data bus (D0 to D7). The status register bit 7 (SR7) is set to “0” at the same time the erase operation starts and is returned to “1” upon comple- tion of the erase operation. In this case, the read status register mode remains active until the read array command (FF16) is writ- ten. ____ The RY/BY Status Flag is “0” during erase operation and “1” when the erase operation is completed as is the status register bit 7. After the erase all blocks end, erase results can be checked by reading the status register. For details, refer to the section where the status register is detailed. qBlock Erase Command (2016/D016) By writing the command code “2016” in the first bus cycle and the confirmation command code “D016” and the block address in the second bus cycle that follows, the block erase (erase and erase verify) operation starts for the block address of the flash memory to be specified. Whether the block erase operation is completed can be confirmed ____ by reading the status register or the RY/BY Status Flag of flash memory control register. At the same time the block erase opera- tion starts, the read status register mode is automatically entered, so that the contents of the status register can be read out. The status register bit 7 (SR7) is set to “0” at the same time the block erase operation starts and is returned to “1” upon completion of the block erase operation. In this case, the read status register mode remains active until the read array command (FF16) is writ- ten. ____ The RY/BY Status Flag is “0” during block erase operation and “1” when the block erase operation is completed as is the status reg- ister bit 7. After the block erase ends, erase results can be checked by read- ing the status register. For details, refer to the section where the status register is detailed. Write 2016 2016/D016 Block address Erase completed NO YES Start Write SR5 = 0 ? Erase error YES NO 2016:Erase all blocks D016:Block erase SR7 = 1 ? or RY/BY = 1 ? Status register read Fig. 120 Erase flowchart |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |