| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/2112 bảng dữ liệu(PDF) 145 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2112 bảng dữ liệu(HTML) 145 Page - Renesas Technology Corp |
|
145 / 894 page ![]() Section 6 Interrupt Controller Rev. 1.00 Mar. 18, 2008 Page 121 of 866 REJ09B0451-0100 • Extended vector mode (EIVS = 1 in SYSCR3) Interrupts KIN15 to KIN8 and KIN7 to KIN0, each form a group. The interrupt exception handling for an interrupt request from the same group is started at the same vector address. Interrupt requests are generated on the falling edge of pins KIN15 to KIN0. Interrupt requests KIN15 to KIN0 can be masked by using KMIMRA and KMIMRB. The status of interrupt requests KIN15 to KIN0 are not indicated. An IRQ6 interrupt is enabled only by input to the ExIRQ6 pin. The IRQ6 pin is only available for a KIN interrupt input, and functions as the KIN6 pin. The initial value of the KMIMR6 bit is 1. For the IRQ7 interrupt, either the IRQ7 pin or ExIRQ7 pin can be selected as the input pin using the ISS7 bit. The IRQ7 interrupt is not affected by the settings of bits KMIMR15 to KMIMR8. The detection of interrupts KIN15 to KIN0 does not depend on whether the relevant pin has been set for input or output. Therefore, when a pin is used as an external interrupt input pin, clear the DDR bit of the corresponding port to 0 so it is not used as an I/O pin for another function. (4) WUE15 to WUE0 Interrupts Interrupts WUE15 to WUE0 are requested by an input signal at pins WUE15 to WUE0. Interrupts WUE15 to WUE0 have the following features: WUE15 to WUE8 and WUE7 to WUE0, each form a group. The interrupt exception handling for an interrupt request from the same group is started at the same vector address Selecting either of the falling edge or the rising edge for interrupt request at pins WUE15 to WUE0 can be made with WUESCR. Interrupt requests WUE15 to WUE0 can be masked by using WUEER. The status of interrupt requests WUE15 to WUE0 is indicated in WUESR. WUESR flags can be cleared to 0 by software The detection of interrupts WUE15 to WUE0 does not depend on whether the relevant pin has been set for input or output. Therefore, when a pin is used as an external interrupt input pin, clear the DDR bit of the corresponding port to 0 so it is not used as an I/O pin for another function. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |