T89C51CC02CA-RATIM datasheet(129/145 Pages) ATMEL

129 / 145 page

129

T89C51CC02

4126D–CAN–05/03

Electrical Characteristics

DC Parameters for

Standard Voltage

A = -40°C to +85°C; VSS = 0 V; VCC = 3 volts to 5.5 volts; F = 0 to 40 MHz

Notes:

1. Operating ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns (See Figure 58.), VIL =

SS + 0.5V,

IH = VCC - 0.5V; XTAL2 N.C.; RST = VCC. ICC would be slightly higher if a crystal oscillator used (See Figure 55.).

2. Idle ICC is measured with all output pins disconnected; XTAL1 driven with TCLCH, TCHCL = 5 ns, VIL = VSS + 0.5V, VIH = VCC -

0.5V; XTAL2 N.C; RST = V

SS (See Figure 56.).

Absolute Maximum Ratings

I = industrial ....................................................... -40

°C to 85°C

Storage Temperature ................................... -65

°C to + 150°C

Voltage on V

CC from VSS ..................................... -0.5V to + 6V

Voltage on Any Pin from V

SS .....................-0.5V to VCC + 0.2V

Power Dissipation ............................................................. 1 W

Note:

Stresses at or above those listed under “Absolute

Maximum Ratings” may cause permanent damage to

the device. This is a stress rating only and functional

operation of the device at these or any other condi-

tions above those indicated in the operational

sections of this specification is not implied. Exposure

to absolute maximum rating conditions may affect

device reliability.

Power Dissipation value is based on the maximum

allowable die temperature and the thermal resistance

of the package.

Table 108. DC Parameters in Standard Voltage

Symbol

Parameter

Min

Typ

(4)

Max

Unit

Test Conditions

VIL

Input Low Voltage

-0.5

0.2Vcc - 0.1

VIH

Input High Voltage except XTAL1, RST

0.2 VCC + 0.9

VCC + 0.5

VIH1

(6)

Input High Voltage, XTAL1, RST

0.7 VCC

VCC + 0.5

VOL

Output Low Voltage, ports 1, 2, 3 and 4

(5)

0.3

0.45

1.0

IOL = 100 µA

IOL = 1.6 mA

IOL = 3.5 mA

VOH

Output High Voltage, ports 1, 2, 3, 4 and 5

VCC - 0.3

VCC - 0.7

VCC - 1.5

IOH = -10 µA

IOH = -30 µA

IOH = -60 µA

VCC = 5V ± 10%

RRST

RST Pulldown Resistor

200

Ω

IIL

Logical 0 Input Current ports 1, 2, 3 and 4

-50

µA

Vin = 0.45V

ILI

Input Leakage Current

±10

µA

0.45V < Vin < VCC

Logical 1 to 0 Transition Current, ports 1, 2, 3

and 4

-650

µA

Vin = 2.0V

CIO

Capacitance of I/O Buffer

Fc = 1 MHz

TA = 25

°C

Power-down Current

160

350

µA3V < V

CC < 5.5V

(3)

Power Supply Current

CCOP = 0.7 Freq (MHz) + 3 mA

CCIDLE = 0.6 Freq (MHz) + 2 mA

T89C51CC02CA-RATIM bảng dữ liệu(PDF) 129 Page - ATMEL Corporation

T89C51CC02CA-RATIM bảng dữ liệu(HTML) 129 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL