ST92F120JR9T datasheet(128/320 Pages) STMICROELECTRONICS

128 / 320 page

128/320

ST92F120 - I/O PORTS

9.5 ALTERNATE FUNCTION ARCHITECTURE

Each I/O pin may be connected to three different

types of internal signal:

– Data bus Input/Output

– Alternate Function Input

– Alternate Function Output

9.5.1 Pin Declared as I/O

A pin declared as I/O, is connected to the I/O buff-

er. This pin may be an Input, an Output, or a bidi-

rectional I/O, depending on the value stored in

(PxC2, PxC1 and PxC0).

9.5.2 Pin Declared as an Alternate Input

A single pin may be directly connected to several

Alternate inputs. In this case, the user must select

the required input mode (with the PxC2, PxC1,

PxC0 bits) and enable the selected Alternate

Function in the Control Register of the peripheral.

No specific port configuration is required to enable

an Alternate Function input, since the input buffer

is directly connected to each alternate function

module on the shared pin. As more than one mod-

ule can use the same input, it is up to the user soft-

ware to enable the required module as necessary.

Parallel I/Os remain operational even when using

an Alternate Function input. The exception to this

is when an I/O port bit is permanently assigned by

hardware as an A/D bit. In this case , after soft-

ware programming of the bit in AF-OD-TTL, the Al-

ternate function output is forced to logic level 1.

The analog voltage level on the corresponding pin

is directly input to the A/D.

9.5.3 Pin Declared as an Alternate Function

Output

The user must select the AF OUT configuration

using the PxC2, PxC1, PxC0 bits. Several Alter-

nate Function outputs may drive a common pin. In

such case, the Alternate Function output signals

are logically ANDed before driving the common

pin. The user must therefore enable the required

Alternate Function Output by software.

WARNING: When a pin is connected both to an al-

ternate function output and to an alternate function

input, it should be noted that the output signal will

always be present on the alternate function input.

9.6 I/O STATUS AFTER WFI, HALT AND RESET

The status of the I/O ports during the Wait For In-

terrupt, Halt and Reset operational modes is

shown in the following table. The External Memory

Interface ports are shown separately. If only the in-

ternal memory is being used and the ports are act-

ing as I/O, the status is the same as shown for the

other I/O ports.

Mode

Ext. Mem - I/O Ports

I/O Ports

P1, P2, P6

WFI

High Imped-

ance or next

address (de-

pending on

the last

memory op-

eration per-

formed on

Port)

Address

Not Affected (clock

outputs running)

HALT

High Imped-

ance

Address

Not Affected (clock

outputs stopped)

RESET

Alternate function push-

pull (ROMless device)

Bidirectional Weak

Pull-up (High im-

pedance when disa-

bled in hardware).

ST92F120JR9T bảng dữ liệu(PDF) 128 Page - STMicroelectronics

ST92F120JR9T bảng dữ liệu(HTML) 128 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL