PIC16F753 datasheet(181/230 Pages) MICROCHIP

181 / 230 page

 2013-2015 Microchip Technology Inc.

DS40001709C-page 181

PIC16F753/HV753

TABLE 22-4:

I/O PORTS

DC CHARACTERISTICS

Standard Operating Conditions (unless otherwise stated)

Param

No.

Sym.

Characteristic

Min.

Typ†

Max.

Units

Conditions

VIL

Input Low Voltage

I/O PORT:

D030

with TTL buffer

—

0.8

4.5V

 VDD  5.5V

D030A

—

0.15 VDD

V2.0V

 VDD  4.5V

D031

with Schmitt Trigger buffer

—

0.2 VDD

V2.0V

 VDD  5.5V

VIH

Input High Voltage

I/O PORT:

D040

with TTL buffer

2.0

—

4.5V

 VDD 5.5V

D040A

0.25 VDD + 0.8

—

2.0V

 VDD  4.5V

D041

with Schmitt Trigger buffer

0.8 VDD

——

2.0V

 VDD  5.5V

D042

MCLR

0.8 VDD

——

IIL

Input Leakage Current(1)

D060

I/O ports

—

0.1

1

AVSS VPIN VDD,

Pin at high-impedance, 85°C

D061

RA3/MCLR(2)

—

0.7

5

AVSS VPIN VDD,

Pin at high-impedance, 85°C

D063

—

0.1

5

A

EC Configuration

IPUR

Weak Pull-up Current(3)

D070*

250

400

AVDD = 5.0V, VPIN = VSS

VOL

Output Low Voltage

D080

I/O Ports (excluding RC4, RC5)

—

0.6

IOL = 7 mA, VDD = 4.5V

-40°C

TA +125°C

IOL = 8.5 mA, VDD = 4.5V

-40°C

TA +85°C

I/O Ports RC4 and RC5

—

0.6

IOL = 14 mA, VDD = 4.5V

-40°C

TA +125°C

IOL = 17 mA, VDD = 4.5V

-40°C

TA +85°C

VOH

Output High Voltage

D090

I/O Ports (excluding RC4, RC5)

VDD-0.7

—

IOH = -2.5 mA, VDD = 4.5V

-40°C

TA +125°C

IOH = -3 mA, VDD = 4.5V

-40°C

TA +85°C

I/O Ports RC4 and RC5

VDD-0.7

—

IOH = -5 mA, VDD = 4.5V

-40°C

TA +125°C

IOH = -6 mA, VDD = 4.5V

-40°C

TA +85°C

These parameters are characterized but not tested.

†

Data in “Typ” column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are

not tested.

Note

Negative current is defined as current sourced by the pin.

The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent

normal operating conditions. Higher leakage current may be measured at different input voltages.

This specification applies to all weak pull-up pins, including the weak pull-up found on RA3/MCLR. When RA3/MCLR is

configured as MCLR Reset pin, the weak pull-up is always enabled.

PIC16F753 bảng dữ liệu(PDF) 181 Page - Microchip Technology

PIC16F753 bảng dữ liệu(HTML) 181 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL