ST72F521 datasheet(141/215 Pages) STMICROELECTRONICS

141 / 215 page

ST72F521, ST72521B

141/215

CONTROLLER AREA NETWORK (Cont’d)

IDENTIFIER LOW REGISTERS (IDLRx)

Read/Write

Reset Value: Undefined

ID[2:0] are the least significant 3 bits of the 11-bit

message identifier.

RTR is the Remote Transmission Request bit. It is

set to indicate a remote frame and reset to indicate

a data frame.

DLC[3:0] is the Data Length Code. It gives the

number of bytes in the data field of the mes-

sage.The valid range is 0 to 8.

DATA REGISTERS (DATA0-7x)

Read/Write

Reset Value: Undefined

DATA[7:0] is a message data byte. Up to eight such

bytes may be part of a message. Writing to byte

DATA7 initiates a transmit request and should al-

ways be done even when DATA7 is not part of the

message.

BUFFER CONTROL/STATUS REGs. (BCSRx)

Read/Write

Reset Value: 00h

Bit 3 = ACC Acceptance Code

− Read Only

Set by hardware with the id of the highest priority

filter which accepted the message stored in the

buffer.

ACC = 0: Match for Filter/Mask0. Possible match

for Filter/Mask1.

ACC = 1: No match for Filter/Mask0 and match for

Filter/Mask1.

Reset by hardware when either RDY or RXIF gets

reset.

Bit 2 = RDY Message Ready

− Read/Clear

Set by hardware to signal that a new error-free

message is available (LOCK = 0) or that a trans-

mission request is pending (LOCK = 1).

Cleared by software when LOCK = 0 to release

the buffer and to clear the corresponding RXIF bit

in the Interrupt Status Register.

Cleared by hardware when LOCK = 1 to indicate

that the transmission request has been serviced or

cancelled.

Bit 1 = BUSY Busy Buffer

− Read Only

Set by hardware when the buffer is being filled

(LOCK = 0) or emptied (LOCK = 1) and reset after

the 2nd intermission bit.

Reset by hardware when the buffer is not ac-

cessed by the CAN core for transmission nor re-

ception purposes.

Bit 0 = LOCK Lock Buffer

− Read/Set/Clear

Set by software to lock a buffer. No more message

can be received into the buffer thus preserving its

content and making it available for transmission.

Cleared by software to make the buffer available

for reception. Cancels any pending transmission

request.

Cleared by hardware once a message has been

successfully transmitted provided the early trans-

mit interrupt mode is on. Left untouched otherwise.

Note that in order to prevent any message corrup-

tion or loss of context, LOCK cannot be set nor re-

set while BUSY is set. Trying to do so will result in

LOCK not changing state.

ID2

ID1

ID0

RTR

DLC3

DLC2

DLC1

DLC0

DATA

ACC

RDY

BUSY

LOCK

ST72F521 bảng dữ liệu(PDF) 141 Page - STMicroelectronics

ST72F521 bảng dữ liệu(HTML) 141 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL