| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PIC16F15213T-I/ST bảng dữ liệu(PDF) 222 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC16F15213T-I/ST bảng dữ liệu(HTML) 222 Page - Microchip Technology |
|
222 / 439 page ![]() Figure 24-2. EUSART Receive Block Diagram ÷ n Multiplier x4 SYNC BRGH BRG16 x16 x64 1 1 1 1 1 x x x 0 0 0 0 0 0 0 n + 1 SPB RG H SPB RG L Bau d Rate Gene rato r FOSC BRG16 SPE N CRE N OERR RCIDL Pin Buffer and Control Data Recove ry RXx/DTx pin Stop (8) 7 Start 0 1 MSb LSb RSR Register RX9 FERR RX9D RCREG Register FIFO 8 Data B us RCxIE RCxIF Inte rrupt Rev. 10-000 114B 2/15/201 7 PPS RXPPS (1) Not e s: 1. In Synchronous mode, the DT output and RX input PPS selectio ns will enable the same pin. 2. In Host Synchronous mode, the TX output and CK input PPS selections will enable the same pin. 1 0 SYNC CSRC PPS CKx Pi n CKPPS (2) 24.1 EUSART Asynchronous Mode The EUSART transmits and receives data using the standard non-return-to-zero (NRZ) format. NRZ is implemented with two levels: a VOH Mark state which represents a ‘1’ data bit, and a VOL Space state which represents a ‘0’ data bit. NRZ refers to the fact that consecutively transmitted data bits of the same value stay at the output level of that bit without returning to a neutral level between each bit transmission. An NRZ transmission port idles in the Mark state. Each character transmission consists of one Start bit followed by eight or nine data bits and is always terminated by one or more Stop bits. The Start bit is always a space and the Stop bits are always marks. The most common data format is eight bits. Each transmitted bit persists for a period of 1/(Baud Rate). An on-chip dedicated 8-bit/16-bit Baud Rate Generator is used to derive standard baud rate frequencies from the system oscillator. See Table 24-2 for examples of baud rate configurations. The EUSART transmits and receives the LSb first. The EUSART’s transmitter and receiver are functionally independent, but share the same data format and baud rate. Parity is not supported by the hardware, but can be implemented in software and stored as the ninth data bit. 24.1.1 EUSART Asynchronous Transmitter Figure 24-1 is a simplified representation of the transmitter. The heart of the transmitter is the serial Transmit Shift Register (TSR), which is not directly accessible by software. The TSR obtains its data from the transmit buffer, which is the TXxREG register. 24.1.1.1 Enabling the Transmitter The EUSART transmitter is enabled for asynchronous operations by configuring the following three control bits: • The Transmit Enable (TXEN) bit is set to ‘1’ to enable the transmitter circuitry of the EUSART • The EUSART Mode Select (SYNC) bit is set to ‘0’ to configure the EUSART for asynchronous operation PIC16F15213/14/23/24/43/44 EUSART - Enhanced Universal Synchronous Asyn... © 2020-2022 Microchip Technology Inc. and its subsidiaries Data Sheet DS40002195E-page 222 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |