| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PIC16F15213T-I/ST bảng dữ liệu(PDF) 182 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC16F15213T-I/ST bảng dữ liệu(HTML) 182 Page - Microchip Technology |
|
182 / 439 page ![]() ...........continued Mode MODE Output Operation Operation Timer Control [4:3] [2:0] Start Reset Stop Monostable 10 000 Reserved 001 Edge-Triggered Start (Note 1) Rising edge start (Figure 21-11) ON = 1 and TMRx_ers ↑ — ON = 0 or Next clock after TxTMR = TxPR (Note 3) 010 Falling edge start ON = 1 and TMRx_ers ↓ — 011 Any edge start ON = 1 and TMRx_ers ↕ — Reserved 100 Reserved Reserved 101 Reserved One Shot 110 Level-Triggered Start and Hardware Reset High-level start and Low-level Reset (Figure 21-12) ON = 1 and TMRx_ers = 1 TMRx_ers = 0 ON = 0 or Held in Reset (Note 2) 111 Low-level start and High-level Reset ON = 1 and TMRx_ers = 0 TMRx_ers = 1 Reserved 11 xxx Reserved Notes: 1. If ON = 0, then an edge is required to restart the timer after ON = 1. 2. When T2TMR = T2PR, the next clock clears ON and stops T2TMR at 00h. 3. When T2TMR = T2PR, the next clock stops T2TMR at 00h but does not clear ON. 21.8 Operation Examples Unless otherwise specified, the following notes apply to the following timing diagrams: • Both the prescaler and postscaler are set to 1:1 (both the CKPS and OUTPS bits). • The diagrams illustrate any clock except FOSC/4 and show clock-sync delays of at least two full cycles for both ON and TMRx_ers. When using FOSC/4, the clock-sync delay is at least one instruction period for TMRx_ers; ON applies in the next instruction period. • ON and TMRx_ers are somewhat generalized, and clock-sync delays may produce results that are slightly different than illustrated. • The PWM Duty Cycle and PWM output are illustrated assuming that the timer is used for the PWM function of the CCP module as described in the “PWM Overview” section. The signals are not a part of the Timer2 module. 21.8.1 Software Gate Mode This mode corresponds to legacy Timer2 operation. The timer increments with each clock input when ON = 1, and does not increment when ON = 0. When the TxTMR count equals the TxPR period count, the timer resets on the next clock and continues counting from zero. Operation with the ON bit software controlled is illustrated in Figure 21-3. With TxPR = 5, the counter advances until TxTMR = 5, and goes to zero with the next clock. PIC16F15213/14/23/24/43/44 TMR2 - Timer2 Module © 2020-2022 Microchip Technology Inc. and its subsidiaries Data Sheet DS40002195E-page 182 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |